Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
This post down below involving A Step-by-Step Guide to Installing a Bathtub is exceedingly motivating. Try it and draw your own personal results.
Mounting a tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging job. If the old bathtub is conveniently easily accessible, the project can relocate quickly; if you have to open up a wall surface to get rid of the old tub and also place the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have qualified on your own for the task and fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is better to think about employing one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This article will certainly help you install a new bathtub in your restroom if you have actually already purchased a new tub and also do not need to transform the plan of your previous water supply pipes.
Your devices and also material list need to comprise the following:
Preparing for the Installation
First of all, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and also check all joints and new pipework for leaks and also tighten them if required. Fill the bath tub as well as also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and securing around the tub should wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines remain in location in between the faucet as well as the sink. Safeguard the faucet in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type must be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall in between the bathroom as well as the tiling, causing problems with dampness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can crack relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the floor tiles using water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on How to Install a Bathtub, I was thinking sharing that excerpt was a smart idea. Remember to take a moment to distribute this post if you liked it. Thank you for your time. Please pay a visit to our site back soon.
Schedule Your Service Report this page